S2000扭矩感測器

Product & Service

德國NCTE 2000系列扭矩感測器—價格實惠的入門扭矩量測

價格實惠、可靠且易於整合。有了2000系列的感測器，無論是靜態或動態扭矩，您都可以快速、容易地測量。感測器的精度為1%，提供0-5V、0-10V、±5V或±10V的模擬輸出訊號。有方軸、圓軸兩種形式可選。

感測器為德國製造，交貨快速。專利磁致伸縮技術—無接觸式測量，可免於磨損。即插即用，不需使用額外的訊號放大器。各型號皆隨附5m的訊號線與校正證書。

應用範圍

測試台
生產線(例如生產線末端的測試)
教學

規格

量測範圍：2.5 Nm至500 Nm，雙向。
轉速：≤ 5000 rpm
精度：≤±1 %
工作溫度：-30 °C至+85 °C
防護等級：IP50
輸出訊號：±10V / ±5V / 0-10V / 0-5V
截止頻率：1000 Hz
形式：方軸 / 圓軸

配件

感測器支架
顯示錶
連軸器

想了解更多資訊? 立即點選上方[型錄下載]。

相關推薦

Torque ranges

Model line Series 2100 Square shaft	Nominal torque bidirectional (+/-) [Nm]	Limit torque unidirectional [Nm]	Limit torque bidirectional (+/-) [Nm]	RPM [rpm]
¼ inch	2.5	2.5	2.5	1000 (A higher speed is possible with backlash-free adaptation)
	5.0	5.0	5.0
	7.5	7.5	7.5
	15	15	10
⅜ inch	60	60	40
½ inch	140	140	85
¾ inch	400	400	270

Note: Series 2100 sensor versions are calibrated to nominal torque. However, the absolute operating limits are as shown in the table above. Do not exceed the specified magnitude of the limit torques for unidirectional and bidirectional loading.

Model line Series 2200 Round shaft	Nominal torque bidirectional (+/-) [Nm]	Limit torque unidirectional [Nm]	Limit torque bidirectional (+/-) [Nm]	RPM [rpm]
Ø 9 mm	2.5	3.25	3.25	5000
	5	6.5	6.5
	7.5	9.75	9.75
	17.5	19.5	19.5
Ø 14 mm	75	97.5	97.5
Ø 19 mm	175	227.5	227.5
Ø 19 mm	250	325	325
Ø 25 mm	500	650	650

Note: In case of overload, the sensor leads to a measurement offset. In this case the sensor must be recalibrated at NCTE AG. The sensor may only be operated within the specified nominal torque range.

Load characteristics

Model line Series 2100 Measuring range	Axial force [N]¹	Limit transverse force [N]	Limit bending moment [Nm]
2.5 and 5	1000	20	2.5
7.5	1000	30	3.7
15	1000	100	12.5
60	2600	300	41.7
140	4000	500	89.5
400	7000	800	176

Model line Series 2200 Measuring range	Axial force [N]¹	Limit transverse force [N]	Limit bending moment [Nm]
2.5 and 5	1000	20	2.5
7.5	1000	30	3.7
17.5	1000	100	12.5
75	2600	300	41.7
175 and 250	4000	500	89.5
500	7000	800	176

Any irregular stress (bending moment, transverse or axial force, exceeding the nominal torque) up to the specified static load limit is only permissible as long as none of the other stresses can occur. Otherwise the limit values must be reduced. If 30 % of the limit bending moment and 30 % of the limit transverse force are present in each case, only 40 % of the axial force is permissible, whereby the nominal torque must not be exceeded.

其他詳細內容可以下載右方產品規格，或預約安排拜訪，由巨克富科技專人詳細為您解說及產品示範。

S2000扭矩感測器

技術諮詢

其他詳細內容可下載產品型錄介紹，或預約安排拜訪，由巨克富科技專人詳細為您解說及產品示範。

Product & Service

Product & Service

產品搜尋

S2000扭矩感測器