Main areas of application for the 2000 Series
Distinctive features
Technical data
Torque ranges
Model line Series 2100 Square shaft |
Nominal torque bidirectional (+/-) [Nm] |
Limit torque unidirectional [Nm] |
Limit torque bidirectional (+/-) [Nm] |
RPM [rpm] |
¼ inch |
2.5 |
2.5 |
2.5 |
1000 (A higher speed is possible with backlash-free adaptation) |
5.0 |
5.0 |
5.0 |
||
7.5 |
7.5 |
7.5 |
||
15 |
15 |
10 |
||
⅜ inch |
60 |
60 |
40 |
|
½ inch |
140 |
140 |
85 |
|
¾ inch |
400 |
400 |
270 |
Note: Series 2100 sensor versions are calibrated to nominal torque. However, the absolute operating limits are as shown in the table above. Do not exceed the specified magnitude of the limit torques for unidirectional and bidirectional loading.
Model line Series 2200 Square shaft |
Nominal torque bidirectional (+/-) [Nm] |
Limit torque unidirectional [Nm] |
Limit torque bidirectional (+/-) [Nm] |
RPM [rpm] |
Ø 9 mm |
2.5 |
3.25 |
3.25 |
5000 |
5 |
6.5 |
6.5 |
||
7.5 |
9.75 |
9.75 |
||
17.5 |
19.5 |
19.5 |
||
Ø 14 mm |
75 |
97.5 |
97.5 |
|
Ø 19 mm |
175 |
227.5 |
227.5 |
|
250 |
325 |
325 |
||
Ø 25 mm |
500 |
650 |
650 |
Load characteristics
Model line Series 2100 Measuring range |
Axial force [N]1 |
Limit transverse force [N] |
Limit bending moment [Nm] |
2.5 and 5 |
1000 |
20 |
2.5 |
7.5 |
1000 |
30 |
3.7 |
15 |
1000 |
100 |
12.5 |
60 |
2600 |
300 |
41.7 |
140 |
4000 |
500 |
89.5 |
400 |
7000 |
800 |
176 |
Model line Series 2200 Measuring range |
Axial force [N]1 |
Limit transverse force [N] |
Limit bending moment [Nm] |
2.5 and 5 |
1000 |
20 |
2.5 |
7.5 |
1000 |
30 |
3.7 |
17.5 |
1000 |
100 |
12.5 |
75 |
2600 |
300 |
41.7 |
175 and 250 |
4000 |
500 |
89.5 |
500 |
7000 |
800 |
176 |
Any irregular stress (bending moment, transverse or axial force, exceeding the nominal torque) up to the specified static load limit is only permissible as long as none of the other stresses can occur. Otherwise the limit values must be reduced. If 30 % of the limit bending moment and 30 % of the limit transverse force are present in each case, only 40 % of the axial force is permissible, whereby the nominal torque must not be exceeded.
© 2019 Chief SI INC. - Design By Armlet